TM 11-5815-246-34P
Explanation
Code
e. Quantity Incorporated in Unit. This column
i n d i c a t e s the quantity of the item, used in the
F Repairable item, When uneco-
e q u i p m e n t , Subsequent appearance of the same
nomically repairable, condemn
item in the same assembly are indicated by the
a n d dispose at the direct support
l e t t e r s "REF",
level.
f. 30-Day DS/GS Maintenance Allowances.
H Repairable item. When uneco-
nomically repairable, condemn
NOTE
and dispose at the general support
Allowances in GS column are for GS
level,
m a i n t e n a n c e only.
D Repairable item. When beyond lower
l e v e l repair capability, return to
( 1 ) The repair parts indicated by asterisk
depot. Condemnation and disposal
entries in separate allowance columns for DS and
not authorized below depot level.
G S represent those authorized for use at that
L Repairable item. Repair, con-
category of maintenance to be requisitioned on an
demnation, and disposal not
" a s required" basis, until stockage is based on
authorized
below
depot/
demand in accordance with AR 710-2.
S p e c i a l i z e d Repair Activity level.
(2) Allowance quantities are indicated in the
A Item requires special handling or
special tool lists section for special tools, TM DE,
c o n d e m n a t i o n procedures because
a n d other support equipment.
of specific reasons (i. e., precious
g. 1-Year Allowances P e r 1 0 0 E q u i p -
m e t a l content, high dollar value,
m e n t s / C o n t i n g e n c y Planning Purposes. C o l u m n
or hazardous
material
critical
i n t e n t i o n a l l y left blank.
material).
h. Depot Maintenance Allowance Per 100
b. Federal Stock Number. Indicates the
E q u i p m e n t s . This column indicates opposite the
F e d e r a l stock number assigned to the item.
first appearance of each item the total quantity
authorized for depot maintenance of 100 equip-
NOTE
ments.
For requisitioning purposes, the Federal
i . Illustration. T h i s c o l u m n i s d i v i d e d a s
stock number must be converted to the
follows:
National stock number by adding
(1) F i g u r e n u m b e r . I n d i c a t e s t h e f i g u r e
"-00-" after the Federal stock
number of the illustration on which the item is
c l a s s i f i c a t i o n (FSC) code (first four
shown in TM 112258.
FSN
For
example,
digits).
(2) Item number. Indicates the item number
6625-553-0142 converts to NSN
or reference designation used to reference the item
i n the illustration.
c. Description. I n d i c a t e s t h e F e d e r a l i t e m
1-4. Special Information
n a m e and a minimum description required to
a. Usable on codes are included in column 3.
identify the item. T h e last line indicates the
U n c o d e d items are applicable to all models.
reference number followed by the applicable
Identification of the usable on codes used in this
Federal Supply Code for Manufacturer (FSCM) in
p u b l i c a t i o n are
parentheses. The FSCM is used as an element in
Used on
Code
i t e m identification to designate manufacturer or
d i s t r i b u t o r or Government agency, etc., and is
BXI
AN/TX C-1
identified in SB 70842.
BXJ
AN/TXC-1A
d. Unit of Measure (U/M). Indicates
the
BXK
AN/TXC-1B
s t a n d a r d or basic quantity by which the listed
BXL
AN/TXC-1C
item is used in performing the actual maintenance
BXM
AN/TXC-1D
f u n c t i o n . This measure is expressed by a two-
c h a r a c t e r alphabetical abbreviation; e.g., ea, in,
b. The following publications pertain to the
pr, etc., and is the basis used to indicate quan-
e q u i p m e n t and its components:
t i t i e s and allowances in subsequent columns.
When the unit of measure differs from the unit of
TM 11-2258
Facsimile Sets AN/TXC
-1, -1A, -lB, -lC, and
issue, the lowest unit of issue that will satisfy the
-1D.
required units of measure will be requisitioned.
