TM 32-5895-248-14&P
( b ) C o n s o l e L i g h t . This light is mounted under
(g) Upper Cabinet Assembly. The upper cabinet
t h e upper cabinet of the center console. It is a 15-watt,
a s s e m b l y is a hinged, door-type shelf cabinet with one
1 8 - i n c h fluorescent lamp with a pushbutton switch and a
adjustable shelf.
r e f l e c t o r shade.
(c) Bulletin Board. A bulletin board is mounted
(4) Corner Cabinet Stabilizer Bracket Set. Rear and
between the upper cabinet and the work surface at the rear
side stabilizer brackets (four of each kind) are used to hold
of the center console. The board consists of a frame-
the tops of the corner consoles to the end and side walls of
mounted tackboard.
the central.
(5) Adjustable Work Surface. The f o r m i c a c o v e r e d
(d) Work Surface Assembly. A f o r m i c a c o v e r e d
work surface assembly is positioned on top and extends out
adjustable work surface is mounted between the two corner
and over the lower cabinet assembly. Below the work
consoles on the end opposite the center console. Four sets
s u r f a c e is a drawer that has slide stops which prevent
of threaded inserts on the work surface of each comer con-
a c c i d e n t a l removal of the drawer. A file folder well is
sole provide four positions for the adjustable work surface.
located at the rear of the work surface.
(6) Edge-Lit Map Board Assembly. T h i s a s s e m b l y
(e) L o w e r C a b i n e t A s s e m b l y . T h i s a s s e m b l y i s
consists of a rubber-faced backboard and two clear plastic
l o c a t e d below the work surface. It has two sliding doors
cover halves that are hinged from each side of the back-
s i m i l a r to the doors described in paragraph (2)(a) above.
board and fastened at the center with large knurled knob
Behind the doors there is a shelf assembly which is adjust-
captive screws. The map board is mounted on two brackets
able to six different positions. There is an access panel to
which are permanently attached to the central's wall.
t h e electrical duct in the rear of the lower cabinet. The
E i g h t fluorescent lamp units are mounted on the frame,
lower cabinet rests on a cabinet base assembly.
t o p , and bottom for edge lighting. On-off switching con-
t r o l s for the lamp units are mounted at each end of the
(3) Corner Console Assembly. There are four corner
l o w e r lighting trough allowing operation from the chair
console assemblies in the central. Each consists of a base
positions.
and air duct assembly, lower cabinet, work surface, bulletin
(7) D i g i t a l C l o c k R e a d o u t A s s e m b l y . T h e c l o c k
b o a r d , electrical duct extension, telephone panel, upper
readout is mounted on a bracket attached to the ceiling in
cabinet, and a light. The individual components are
f r o n t of the map board. It is a remote digital slave unit
described in detail below.
used in an OUTS and needs a master clock for operation.
(8) Rotary Chair. The rotary chair is provided with a
(a) Base and Air Duct Assembly. A base and air
tie down assembly which is directly beneath the centermost
d u c t assembly is provided below the lower cabinet, and
of the chair. The tiedown assembly locks into a floor socket
supports the corner console.
for transport.
(b) Lower Cabinet Assembly. The l o w e r c a b i n e t
(9) Special Electrical Duct. Four special electrical
is similar to the cabinet described in paragraph (2)(e)
ducts in the central are located behind each corner console
above, except it has no access panel and is smaller.
and extend from the floor to the top of the corner console.
Each duct has a passthru, with a gasket between it and the
(c) W o r k S u r f a c e A s s e m b l y . T h i s a s s e m b l y i s
similar to the center console work surface assembly
e l e c t r i c a l duct extension assembly. Each duct also has a
described in paragraph (2)(d) above, except it is smaller and
side access panel. The electrical duct on the center console
h a s an ash tray. It also has a removable equipment tray
end next to the map board has two open neoprene flaps on
mounted on the surface that serves as a mount for the cal-
the top of the duct, allowing the wires for the clock and the
culator or one of the two typewriters.
map board to pass through.
(d) Bulletin Board. The bulletin board is similar
( 1 0 ) Telephone Set TA-676(*)/G. A telephone set is
t o that used in the center console, except that it is L-
normally mounted on the electrical duct extension assem-
Shaped and fits in the corner of the console.
bly of corner console number one. It maybe moved to any
(e) Electrical Duct Extension Assembly. An e l e c -
of the other three comer consoles as operational require-
t r i c a l duct extension assembly is mounted between the
ments dictate. It is part of an intercom system in an OUTS
work surface and the upper cabinet. It has provisions for
c o m p l e x and requires a switchboard for operation. The
two convenience receptacles, a blackout circuit switch, an
t e l e p h o n e is connected to external feedthru in the "M"
A - p h a s e circuit breaker, and a light circuit breaker. The
h o l e on the central's end wall on the right side of the
t e l e p h o n e mounting panel is also mounted on the duct
center console. The other feedthru is a panel assembly on
extension.
the opposite end wall. Power is supplied to the telephone
by a receptacle on the electrical duct extension assembly of
(f) C o n s o l e L i g h t . This light is identical to the
unit described in paragraph (2)(b) above.
each corner console. Refer to paragraph (3)(e) above.
1-4
