TM 11-7025-214-40P
Application/Explanation
Code
D --Support items that are removed, replaced, used
design and characteristics of the item by means of its
engineering drawings, specifications, standards, and in-
at depot, mobile depot, specialized repair ac-
spection requirements to identify an item or range of
tivity only.
items.
(b) The maintenance code entered in the fourth
position indicates whether the item is to be repaired
NOTE
and identifies the lowest maintenance level with the
When a stock numbered item is requisi-
capability to perform complete repair (i.e., all author-
tioned, the repair part received may have a
ized maintenance functions). This position will contain
different part number than the part being
one of the following maintenance codes:
replaced.
Application/Explanation
Code
f. Description. Indicates the Federal item name and,
F --The lowest maintenance level capable of complete
if required, a minimum description to identify the item.
repair of the support item is the direct support
g. Unit of Measure (U/M). Indicates the standard of
level.
the basic quantity of the listed item as used in perform-
H --The lowest maintenance level capable of complete
ing the actual maintenance function. This measure is
repair of the support item is the general support
expressed by a two-character alphabetical abbreviation
level.
(e.g., ea, in, pr, etc). When the unit of measure differs .
D --The lowest maintenance level capable of complete
from the unit of issue, the lowest unit of issue that will
repair of the support item is the depot level.
satisfy the required units of measure will be requisi-
L --Repair restricted to designated specialized repair
tioned.
activity.
h. Quantity Incorporated in Unit. Indicates the quan-
Z --Nonreparable. No repair is authorized.
tity of the item used in the breakout shown on the
(3) Recoverability code. Recoverability codes are
illustration figure, which is prepared for a functional
assigned to support items to indicate the disposition
group, subfunctional group, or an assembly.
action on unserviceable items. The recoverability code
is entered in the fifth position of the Uniform SMR
4. Special Information
Code format as follows:
a. The following publications pertain to the AN/
UYH1 and its components:
Recoverability
Codes
Definition
TM 11-7025-214-23P, Magnetic Tape Unit AN/UYH-
Z --Nonreparable item. When unserviceable, con-
1
demn and dispose at the level indicated in po-
sition 3.
TM 11-7025-214-30, Magnetic Tape Unit AN/UYH-l
F --Reparable item. When uneconomically reparable,
condemn and dispose at the direct support level.
TM 11-7025-214-40, Magnetic Tape Unit AN/UYH-1
H --Reparable item. When uneconomically reparable,
condemn and dispose at the general support
b. National stock numbers (NSN'S) that are missing
level.
from P source coded items have been applied for and
D --Reparable item. When beyond lower level repair
will be added to this TM by future change/revision when -
capability, return to depot. Condemnation and
they are entered in the Army Master Data File (AMDF).
disposal not authorized below depot level.
Until the NSN'S are established and published, submit
L --Reparable item. Repair, condemnation, and dis-
exception requisitions to: Commander, US Army Com-
posal not authorized below depot/specialized
municationsElectronics Command and Fort Mon-
repair activity level.
mouth, ATTN: AMSEL-MM, Fort Monmouth, NJ
C. National Stock Number. Indicates the National
07703-5007 for the part required to support your equip-
stock number assigned to the item and will be used for
ment.
requisitioning purposes.
c. In some cases, selected capacitor and resistor val-
d. Federal Supply Code for Manufacturer (FSCM).
ues have a large range specified. Based on factory repair
The FSCM is a 5-digit numeric code listed in SB 708-
records the most probable replacement values have been
41/42 which is used to identify the manufacturer, dis-
specified. Where necessary, values other than those
tributor, or Government agency, etc.
specified may be used in order to repair the hardware.
e. Part Number. Indicates the primary number used
The allowable values of these resistors and capacitors
by the manufacturer (individual, company, firm, cor-
are stated in the appropriate section in the manual.
poration, or Government activity), which controls the
2
