TM 11-5930-201-14P
Code
Explanation
A-
Item requires special handling or condemnation procedures because of specific reasons (i.e., precious
metal content, high dollar value, critical material or hazardous material).
b. Federal Stock Number. Indicates the Federal stock number assigned to the item and will be used for
requisitioning purposes.
c. Description. Indicates the Federal item name and a minimum description required to identify the item.
The last line indicates the reference number followed by the applicable Federal Supply Code for Manufacturer
(FSCM) in parentheses. The FSCM is used as an element in item identification to designate manufacturer or
distributor or Government agency, etc., and is identified in SO 708-42.
d. Unit of Measure (UIM). Indicates the standard or basic quantity by which the listed item is used in
performing the actual maintenance function. This measure is expressed by a two-character alphabetical
abbreviation, e.g., ea. in, pr, etc., and is the basis used to indicate quantities and allowances in subsequent
columns. When the unit of measure differs from the unit of issue, the lowest unit of issue that will satisfy the
required units of measure will be requisitioned.
e. Quantity Furnished with Equipment (Basic Issue Items Only). Not applicable.
f. Quantity Authorized (Items Troop Installed or Authorized Only). Not applicable.
g. Quantity Incorporated in Unit. This column indicates the quantity of the item used in the equipment.
Subsequent appearances of the same item in the same assembly are indicated by the letters "REF".
h. 15-Day Organizational Maintenance Allowances.
(1) The repair parts indicated by an asterisk in the allowance column represent those authorized for use
at the organizational category, and will be requisitioned on an "as required" basis, until stockage is based on
demand in accordance with AR 710-2.
(2) Major Army commanders are authorized to approve reduction in the range of support items
authorized for use in units within their commands. Recommendations for increase in range of items authorized
for use will be forwarded to the Commanding General, US Army Electronics Command, ATTN: AMSEL-MA-
CR, Fort Monmouth, NJ., 07703.
(3) Allowance quantities are indicated in the special tools list section for special tools, TMDE, and other
support equipment.
i. 30-Day DSIGS Maintenance Allowances.
NOTE
Allowances in GS column are for GS
maintenance only.
(1) The repair parts indicated by asterisk entries in separate allowance columns for DS and GS represent
those authorized for use at that category of maintenance to be requisitioned on an "as required" basis, until
stockage is based on demand in accordance with AR 710-2.
(2) Allowance quantities are indicated in the special tool lists section for special tools, TMDE, and other
support equipment.
j. 1-Year Allowances Per 100 Equipments Contingency Planning Purposes. Column intentionally left
blank.
k. Depot Maintenance Allowance Per 100 Equipments. This column indicates opposite the first
appearance of each item the total quantity authorized for depot maintenance of 100 equipments.
I. Illustration.
(1) Figure number. Not applicable.
(2) Item number. Indicates the item number or reference designation used to identify the item.
1-4. Special Information
Usable on codes are included in column 3. Uncoded items are applicable to all models. Identification of the
usable on codes used in this publication are-
Code
Used on
A4K
SA-331/U
1-5. Location of Repair Parts
a.
This manual contains one cross reference index (sec IX) to be
used to
locate a
repair part when either
the Federal stock number or reference number (manufacturer's part number) is known. The first column in the
index is prepared in numerical or alphanumeric sequence in ascending order. The reference numbers
(manufacturer's part numbers) -are listed immediately following the last listed Federal stock number in the
index of Federal stock numbers.
b. When the Federal stock number or reference number is known, follow the procedures given in (1) and
(2) below.
(1) Refer to the index of Federal stock numbers (sec IX), and locate the Federal stock number or
reference number. The FSN and reference number are cross-referenced to the applicable figure and item
number or reference designation.
(2) Refer to the repair parts list (sec V and VII) and locate the figure number (col 7a-20P, 10a-34P) and
item number or reference designation (col 7b-20P, 10b-34P) as noted in the FSN index.
4